HID VertX V100 Door & Reader Interface
HID VertX V100 Door & Reader Interface - Access Control Processing for Two Readers / Two Doors
The HID VertX V100 provides access control processing for two readers and up to two doors. It connects via Wiegand or Clock-and-Data to card readers and via RS-485 to the V1000 master controller, which handles TCP/IP communications. The V100 features polycarbonate enclosure, silk-screened connections, offline processing based on facility code, supervised input reporting, and real-time command processing. UL 294 and UL 1076 recognised components. Dimensions: 5.8 x 4.825 x 1.275 inches.
The HID VertX™ Products provide a complete and fully features hardware/firmware intrastructure for biometric access control software host systems.
The HID VertX V100 Door / Reader Interface conects two biometric access control card readers via Wiegand or Clock-and-Data interface controlling either one or two doors. The V100 features on-board flash memory, allowing program updates to be downloaded via the network.
The HID VertX V100 connects t0 HID V1000 through a high speed RS-485 network. The HID V1000, in turn, communicates with the system host via industry standard TCP/IP protocol over 10/100 Mbps Ethernet or the internet. This architecture minimizes the impact on corporate LANs by using only on TCP/IP address for every 32 interfaces and by handling low-level transactions on the RS-485 network.
- Reports supervised inputs.
- Connects to the HID VertX EVO V1000 via RS-485.
- Receives and processes real time commands from the HID VertX V1000.
- Reports all activity to the HID VertX V1000.
- Attractive polycarbonate enclosure protects components from damage.
- All connections and indicators are fully identified by silk-screened nomenclature on the cover.
- Processes off-line access control decisions based on facility code.
- UL 294 and UL 1076 recognized components.
Technical Specification :
| Dimensions: | 5.8"W x 4.825"H x 1.275" D (147.32 mm x 122.55 mm x 32.38 mm) |
| Weight: | 12.4 oz (0.35 kg) |
| Power Supply Requirements: | 60 mA @ 9-18 VDC (with no readers connected) Recommended: Supervised linear power supply with battery backup, input surge protection, and AC fail and battery low contact outputs. When VertX is supplying power to readers the requirements are 600 mA @ 9-18VDC. The V100 can supply 500 mA to two readers |
| Cable Distance: | |
| RS-485: | 4000 feet (1220 m) to host, using Belden 3105A, 22AWG twisted pair, shielded 100? cable Wiegand - 500 feet (150 m) to reader - using ALPHA 1299C 22AWG, 9-conductor, stranded, overall shield (Fewer conductors needed if all control lines are not used) |
| Input Cirbuits: | 500 feet (150 m), 2-conductor, shielded, using ALPHA 1292C (22AWG) or Alpha 2421C (18AWG) |
| Output Cirbuits: | 500 feet (150 m), 2-conductor, usingALPHA 1172C (22AWG) or Alpha 1897C (18AWG) Minimum wire gauge depends on cable length and current requirements. |
Frequently Asked Questions
What two-door processing does the VertX V100 provide?
It connects two card readers via Wiegand/Clock-and-Data and controls one or two doors.
UL listings?
UL 294 and UL 1076 recognised components.
What is the RS-485 cable distance?
Up to 4000 feet (1220 m) to host using Belden 3105A 22AWG twisted pair.
Dimensions?
5.8 x 4.825 x 1.275 inches (147.32 x 122.55 x 32.38 mm).
Power supply?
60 mA at 9-18 VDC with no readers; 600 mA with readers powered by the V100.